Peugeot 3008 Key Fob Problems
Peugeot's 3008 SUV is a mid-sized model with a lot of positives. It's stylish, handles well, and has a big boot. Can it be competitive in the most crowded segment of the market, perhaps?
If your Peugeot keyfob fails to function it is possible that it was exposed to soapy or clean tap water. It is possible to take off the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by a coin-sized battery. This power is used to operate the remote locking system, as well as other functions. This battery has a limited life span and may wear out over the course of years of use. A simple way to check whether the battery is damaged is by performing the voltage test. A multimeter can measure the voltage between the battery's plus and poles. The results of this test will indicate whether the battery is dead or not.
The receiver module could be the reason for your key fobs failing to function after you've used your Peugeot 3008 for a long time. The receiver module is responsible for receiving radio frequency signals from the key fobs and sending them to the car's system. If the receiver module has a fault, it won't be able to transmit commands to other modules within the car.
Sweat or moisture on the circuit board is another common reason for an inoperable key fob. This can result in short circuits that cause the battery to be depleted and disable the feature that locks the fob's remote. If this happens, you should take your key fob in to an expert in chip level repair to fix it.
Water damage
If you dropped your key fob in the pool, tossed it in the wash or left it in the rain for too long, water damage can be a real problem. Water is a good conductor and can easily cause short circuits on the circuit board. It can also cause corrosion to metal traces on the key fob as well as other components. A wet circuit board can also cause the battery lose its charge.
If you have a spare key fob, use it to lock or unlock your Peugeot 3008 to rule out the possibility that a dead battery is the source of the problem. Interference signals can cause your key fob to cease working properly. They interfere with the signal generated by the receiver module. These signals can be caused by a variety of sources such as radio transmitters in the close vicinity.
If you hear sloshing sounds coming from your Peugeot 3008 when driving this could be due to a clogged condensate drain for the evaporator. You can test for this by looking for the drain holes beneath your door and blowing compressed air into them. You can also use a flexible wire to wiggle the drain holes and wash away any dirt that may have been accumulating there. Air pockets can also be identified by sloshing sounds.
The receiver module is not working properly.
The receiver module of a Peugeot 3008 is responsible for transmitting a remote keyless signal from the keyfob into the receiver inside the car. This module can be damaged and block the car from acknowledging your key fob. This issue can also be caused by an inactive battery or water damage. It could also be caused by interference from electronic devices operating on the same frequency. In these instances the car could display the message "card not detected" on the display.
Luckily, there are a number of ways to fix this problem. You can try to replace the battery or reprogram the key fob. You may also be able to start the vehicle with a spare key. If G28 fob isn't working after all these steps, then it could have a faulty chip.
It is best to remove the chip and clean it using paper towels and rubbing alcohol. If the chip has been damaged, you should purchase an entirely new one. FB Series enclosures are designed for use with a key fob. They come with an additional coin battery holder for cell batteries that fits the most popular type of key fob batteries. They can also be customized by using digital printing or CNC cutouts that are machined. If your key fob has been exposed to dirty or salty tap water, the chip might be contaminated and need to be cleaned.
Keyless entry system that isn't working properly
If you get the message "card not detected" this means that your car cannot receive signals from your key fob. This could be due to many reasons including the battery being weak or dead. Most often, the issue can be solved by pressing the start button with the key fob. In certain instances however, you may have to take the key fob to an Peugeot dealership for additional repairs.
The first step to fix a Peugeot 3008 key fob that's not able to unlock or lock the doors is to test the battery. Batteries are often the cause of a malfunctioning key fob. However there are other reasons that could be involved. These include worn buttons and water damage.
If you've recently had your Peugeot key fob exposed to clean tap water, it's a good idea to remove the battery and dry the electronic components using paper towel. You could also try using isopropyl ethanol or a cleaner to accomplish this. It's best to change the fob after it has been exposed to salt water or soapy water.
If your key fob not working, try to reset it by disconnection of the battery that is 12 volts for approximately 15 minutes. Then, reconnect the negative cable first, followed by the positive cable.